Imaxrc® The most professional manufacturer of balance charger in China.

UNIVERSAL ULTRABOOK AND TABLET POWER SUPPLY

  FEATURES

This product is designed to supply USB devices and tablet computers with power, providing five different output voltages to select from. The connected load’s current consumption must not exceed the maximum output rating of the product. Power is supplied via a standard mains socket (100 - 240 V/AC, 50/60 Hz). The product should only be used in dry indoor areas. The product features both short-circuit and overload protection.
For safety and approval purposes (CE), you must not rebuild and/or modify this product. If you use the product for purposes other than those described above, the product may be damaged. In addition, improper use can cause hazards such as short circuiting, fire, electric shock etc. Read the instructions carefully and keep them. Make this product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All company names and product names are trademarks of their respective owners. All rights reserved.

 SAFETY INSTRUCTIONS

Read the operating instructions carefully and especially observe the safety information. If you do not follow the safety instructions and information on proper handling in this manual, we assume no liability for any resulting personal injury or damage to property. Such cases will invalidate the warranty/guarantee.
a) Persons / Product
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may become dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity, moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and protect it from any accidental use. Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage the product.
• Also observe the safety and operating instructions of any other devices which are connected to the product.
b) Miscellaneous
• Consult an expert when in doubt about operation, safety or connection of the device.
• Maintenance, modifications and repairs are to be performed exclusively by an expert or at a qualified shop.

 DISPOSAL

This symbol on the product or in the instructions means that your electrical and electronic equipment should be disposed at the end of its life separately from your household waste. There are separate collection systems for recycling in the EU.
For more information, please contact the local authority or your retailer where you purchased the product.

 
  HOW TO USE

a) Connecting an electric load
• Disconnect the power supply unit from the mains socket before replacing
the low-voltage plug or resetting the output voltage.
• The power adaptor‘s output voltage must match the input voltage of the
electric consumer.
1. Set the required output voltage with the voltage selection switch, using the voltage setting key. When making settings always be sure the arrow points accurately to the respective voltage marking.
2. Select one of the three low-voltage plugs (DC cable) matching the input socket and polarity of the electric consumer (see table).
3. Connect the plug to the connector at the end of the output cable. Voltage reversal of the output plug is not possible for security reasons. The inner contact is positive (+), the outer negative (–).
4. Connect the low-voltage plug to the switched-off consumer.
5. Connect the mains plug to a standard mains socket (100 - 240 V/AC, 50/60 Hz). The EILI logo on the top of the power adaptor lights up to indicate operational readiness.
6. Now switch the connected consumer on. If it does not function properly, switch it off immediately and disconnect it from the power supply unit.
7. Remove the power supply unit from the mains when it is no longer in use.
b) Connecting a USB load
1. Select one of the four low-voltage plugs (microUSB type B) matching the input socket of the electric consumer.
2. Connect the plug to the connector at the end of the USB cable.
3. Connect the switched-off consumer to the low-voltage plug.
4. Connect the USB cable to the power adaptor.

The power adaptor can also be used to operate / charge a normal USB device. Plug the USB plug of the device into the USB socket and continue with point 5.

5. Connect the mains plug to a standard mains socket (100 - 240 V/AC, 50/60 Hz). The EILI logo on the top of the power adaptor lights up to indicate operational readiness.
6. Now switch the connected consumer on. If it does not function properly, switch it off immediately and disconnect it from the power adaptor.
7. Remove the power adaptor from the mains when it is no longer in use.

The USB output and other electric loads can be operated in parallel. However, make sure that the power input of the connected devices does not exceed the power supply unit’s total power output.

  SPECIFICATIONS

Input Voltage: 100-240V AC
Output Voltage: 9 / 10.5V 3A
12 / 15 / 19V 1.5A
USB Output: 5V 2.1A
Output Power: 45W Max
Dimensions: 35WX108HX70Dmm
Weight: 230g

  CONNECTOR PLUGS AND CABLES